| MAKE | MODEL | CHASSIS | SYMPTOM | CURE | |
| PHILIPS | N/A | 25N5 | NARROW RASTER - MAY ALSO HAVE FAINT JAILBARS | CHECK/REPLACE C508 WITH 10nF @ 50v (P/N# 483512147461) | |
| PHILIPS | N/A | 25N5 | NO HORZ. SYNC. OR SET HAS A BLUE SCREEN | CHECK PIN #5 OF IC530 IS HIGH AND ALL INPUTS ARE NORMAL, THEN REPLACE IC530 | |
| PHILIPS | N/A | 25P1 | RELAY CHATTERS | CHECK/REPLACE C405 FOR OPEN | |
| PHILIPS | N/A | 25P1 | REMOTE 'OFF' BUTTON MUST BE PRESSED TWICE TO TURN SET OFF. | CHECK/REPLACE IR90 INFRARED RECEIVER | |
| PHILIPS | N/A | 25P1 | SET SHUTS OFF AT RANDOM | CHECK/REPLACE IC350 | |
| PHILIPS | N/A | 25P1 | INTERMITTENT SHUTDOWN | CHECK/REPLACE R663 | |
| PHILIPS | N/A | 25P1 | INTERMITTENT SHUTDOWN AND INTERMITTENT HORZ. DRIVE | CHECK/REPLACE C208 FOR LEAKAGE | |
| PHILIPS | N/A | 25P1 | HISS IN SPKRS. W/TV OFF--POP IN SPKR AT TURN ON | REMOVE D280 AND INSTALL NEW DIODE P/N 4835 130 37048 | |
| PHILIPS | N/A | 25P1 | INTERMITTENT SHUTDOWN | CHECK/REPLACE R429 | |
| PHILIPS | N/A | 25P1 | BENDING OR TEARING OF THE PIX - MAYBE THERMAL AND ALSO VARY FROM SIGNAL AND AGC LEVELS. | REPLACE IC200 (483520987072) | |
| PHILIPS | N/A | 25P1 | BLOWS Q420 IMMEDIATELY | CHECK D430 FOR SHORTS | |
| PHILIPS | N/A | 25P1 | OSD MENU SKIPS THE STEREO AND AUX INPUT FEATURES | CHECK/REPLACE D261 | |
| PHILIPS | N/A | 25P1 | NO VIDEO | CHECK/REPLACE C608 FOR SHORT AND R622 FOR OPEN | |
| PHILIPS | N/A | 25P1 | SET IS SHUTTING DOWN | CHECK/REPLACE R11 (CRT BOARD) FOR OPEN | |
| PHILIPS | N/A | 25P1 | ERRATIC OSD WHEN SET IS HOT | CHECK/REPLACE IC350 | |
| PHILIPS | N/A | 25P1 | SLOW COLOR LOCK AFTER CHANNEL CHANGE | USE SELECTED CRYSTAL WITH BLUE MARK ON CASE | |
| PHILIPS | N/A | 25P1 | SLOW CHANNEL ACQUISTION IN THE CABLE MODE | CHECK/REPLACE IC380 (5 VOLT SOURCE) | |
| PHILIPS | N/A | 25P1 | BRIGHT SCREEN WITH RETRACE LINES - NO VIDEO | CHECK Q630,Q631,Q632 | |
| PHILIPS | N/A | 25P1 | JAIL BARS ON THE LEFT SIDE OF THE SCREEN | CHECK/REPLACE L502 WITH NEW TYPE (483515757336) | |
| PHILIPS | N/A | 25P1 | NO COLOR AND VOLTAGES ON IC600 PINS#12,13,14 ARE LOW | CHECK/REPLACE IC600 | |
| PHILIPS | N/A | 25P1 | RADIO INTERFERENCE,DOTS,SWIRLS OR HERRINGBONE SEEN ON PIP VERSIONS. | CHECK/REPLACE PIP MODULE (ISOLATE BY UNPLUGGING J602) | |
| PHILIPS | N/A | 25P1 | POOR CONTRAST NO COLOR WHEN COLD | REPLACED C450 | |
| PHILIPS | N/A | 25P1 | PIP DISAPPEARS ON VIDEO GAMES | DO NOT ATTEMPT TO USE PIP WITH NON STANDARD SIGNALS | |
| PHILIPS | N/A | 25P1 | LOW B+ AND NO RASTER | CHECK/REPLACE IC400 | |
| PHILIPS | N/A | 25P1 | SET WILL COME ON ONCE AND THEN WON'T SHUT OFF OR IT WILL SHUT OFF AND NOT COME BACK ON. | CHECK/REPLACE IC350 (MICRO-PROCESSOR) | |
| PHILIPS | N/A | 25P1 | NO COLOR | CHECK/REPLACE R614 FOR A CHANGE IN VALUE | |
| PHILIPS | N/A | 25P1 | INTERMITTENT OPERATION - LEDS WOULD LIGHT FOR A SECOND | CHECK/RESOLDER CONECTIONS ON C451 (NEAR FLYBACK) | |
| PHILIPS | N/A | 25P1 | DEAD SET AFTER MANY POWER SUPPLY COMPONENTS CHANGED | CHECK L422 FOR OPEN | |
| PHILIPS | N/A | 25P1 | INTERMITTENT SHUTDOWN OR INTERMITTENT START-UP | CHECK FOR COLD SOLDER CONNECTIONS ON D430 OR C431 | |
| PHILIPS | N/A | 25P1 | TUNING SLOW TO LOCK IN WHILE IN THE CABLE MODE | REPLACE THE MICROCOMPUTER IC | |
| PHILIPS | N/A | 25P1 | DEAD SET - 5 VOLTS NORMAL BUT RESET LINE LOW | CHECK/REPLACE IC351 | |
| PHILIPS | N/A | 25P1 | 130 VOLT SOURCE IS TOO LOW | CHECK/REPLACE R431 AND IC400 | |
| PHILIPS | N/A | 25P1 | SET GOES OFF INTERMITTENTLY--APPEARS TO SHUTDOWN | CHECK FOR CORRECT SETTING OF THE B+ (130 VOLTS) | |
| PHILIPS | N/A | 25P1 | HIGH PITCHED SQUEAL FROM POWER SUPPLY WHILE ON | REPLACE L421 USING ONLY P/N 483515757054 | |
| PHILIPS | N/A | 25P1 | SET COMES ON WITH AUX.VIDEO BUT TUNER AUDIO | REPLACE IC350 WITH NEW VERSION | |
| PHILIPS | N/A | 25P1 | BRIGHT SCREEN WITH RETRACE LINES | CHECK/REPLACE R663 FOR OPEN | |
| PHILIPS | N/A | 25P1 | NO VERTICAL SWEEP | CHECK/REPLACE R445 FOR OPEN | |
| PHILIPS | N/A | 25P1 | POOR REGULATION AFTER Q420 WAS REPLACED | REPLACE R427,R428 AND R424 | |
| PHILIPS | N/A | 25P1 | DISTORTED AUDIO W/SET ON--HUM OR BUZZ W/SET OFF | C284 AND/OR C294 MISSING --CHECK FOR PRESENCE OF | |
| PHILIPS | N/A | 25P1 | VERTICAL SWEEP STRETCHED SEVERLY | CHECK/REPLACE IC550 | |
| PHILIPS | N/A | 25P1 | DEAD SET WITH NO STANDBY POWER | CHECK/REPLACE Q420 AND R424 | |
| PHILIPS | N/A | 25P1 | REPEATED FAILURE OF Q420 (FET) | CHECK/REPLACE C412 WITH A 100nF (MAY HAVE A 10nF FROM THE FACTORY) | |
| PHILIPS | N/A | 25P1 | NO HORZ. DRIVE FROM PIN 26 OF IC200 | CHECK/REPLACE C222 FOR OPEN | |
| PHILIPS | N/A | 25P1 | DEAD SET ,POWER SUPPLY FAILURE | CHECK TO SEE IF R429 IF TOUCHING C450 | |
| PHILIPS | N/A | 25P1 | SET WILL NOT TURN OFF EVEN BY GROUNDING COLLECTOR OF Q433 | CHECK/REPLACE IC402 | |
| PHILIPS | N/A | 25P1 | SET SHUTS DOWN DURING SCENE CHANGES OR CHANGING CHANNELS | CHECK/REPLACE D661,R663 AND Q661 | |
| PHILIPS | N/A | 25P1 | POWER SUPPLY GOES INTO SHUTDOWN AT POWER ON OR CHANNEL CHANGE OR SCENE CHANGES. | CHECK/REPLACE R430 (110K) FOR CHANGE IN VALUE. | |
| PHILIPS | N/A | 25P1 | WASHED OUT PIX - CONTRAST CONTROL HAS NO EFFECT | CHECK/REPLACE Q661 | |
| PHILIPS | N/A | 25P1 | R429 GETS VERY HOT AFTER A FEW MINUTES | CHECK C430 FOR SHORT ALSO D430 | |
| PHILIPS | N/A | 25P1 | NO AUDIO OR VIDEO BUT OSD WORKS OK | CHECK/REPLACE L210 | |
| PHILIPS | N/A | 25P1 | 130 VOLT SOURCE IS TOO HIGH | CHECK/REPLACE R430 AND R432 FOR A CHANGE IN VALUE | |
| PHILIPS | N/A | 25P1 | HIGH FREQUENCY SQUEAL | REPLACE L421 | |
| PHILIPS | N/A | 25P1 | SET SHUTS OFF INT. OR WON'T EVEN COME ON | CHECK C431 OR CONNECTIONS ON IT | |
| PHILIPS | N/A | 25P1 | SLOW OR NO COLOR LOCK POSSIBLY ON SOME CHANNELS ONLY AND THIS SET DID HAVE NEW STYLE CRYSTAL WITH BLUE MARKINGS. | CHECK/REPLACE IC600 | |
| PHILIPS | N/A | 25P1 | NOISY OR SQUEALING SOUND COMING FROM SWITCHING TRANSFORMER | CHECK/REPLACE R410 OR R421 FOR OPEN | |
| PHILIPS | N/A | 25P1 | SET SHUTS DOWN BUT WITH SCREEN CTRL. ALL THE WAY DOWN, THE SET WILL REMAIN TO RUN WITH WHITE SCREEN WITH RETRACE. | CHECK/REPLACE R11 (100 OHM) ON THE CRT BOARD -- (200 VOLT SOURCE) | |
| PHILIPS | N/A | 25P1 | INTERMITTENT DEAD SET | CHECK/RESOLDER C431 | |
| PHILIPS | N/A | 25P1 | VERTICAL ROLL ON SOME CABLE CHANNELS | CHANGE R603 TO A 2k | |
| PHILIPS | N/A | 25P1 | ROLLING/FLAGING/HORZ. TEARING AT TOP OF PICTURE | REPLACE IC200 WITH NEW VERSION (TDA4505B) (USE 483531057062) | |
| PHILIPS | N/A | 25P1 | DEAD SET AND RESET PIN #33 STAYS AT 1.5 VOLTS | CHECK/REPLACE IC351 | |
| PHILIPS | N/A | 25P1 | VOLTAGE AT Z430 IS NOT 5.6v | CHECK/REPLACE Z430 FOR CHANGE OF VALUE | |
| PHILIPS | N/A | 25P1 | DEAD SET | CHECK/REPLACE Q420,D430,R427,R428 AND R424. | |
| PHILIPS | N/A | 25P1 | NO COLOR WHEN COLD | CHECK/REPLACE IC600 | |
| PHILIPS | N/A | 25P1 | OSD GOOD BUT NO OFF-AIR VIDEO | CHECK L210 LEAD DRESS (POSSIBLY SHORTING TO ITS OWN SHEILD) | |
| PHILIPS | N/A | 25P1 | NO COLOR ON SOME CHANNELS-INT. LOSS OF COLOR | CHNG. C620 TO 10pF | |
| PHILIPS | N/A | 25P1 | SET TURNS ON THEN MICROPROCESSOR LOCKS UP - WILL NOT TURN BACK OFF - SNOWY RASTER LOCKED ON ONE CHANNEL | CHECK/REPLACE Q337 | |
| PHILIPS | N/A | 25P5 | VIDEO SMEARS ON BRIGHT OBJECTS | ADD 1meg (P/N# 483511657322) FROM PIN #52 OF IC270 TO GROUND | |
| PHILIPS | N/A | 25P5 | ERRATIC OPERATION - SELF ACTIVATION OF CHANNELS,ON/OFF, VOLUME - INTERMITTENT PROBLEM | CHECK/REPLACE KEYBOARD SWITCHES (LEAKY) (P/N# 483527657004) WHICH INCLUDES ALL 7 SWITCHES | |
| PHILIPS | N/A | 25P5 | TOP OF PICTURE FOLDED OVER OR COMPRESSED AFTER SET IS WARM | CHECK/REPLACE YOKE (P/N# 483515017116) | |
| PHILIPS | N/A | 25P5 | VERY SNOWY PICTURE AT 0dB SIGNAL LEVEL | CHECK/REPLACE R222 OPEN (12kê) (P/N# 483511657397) | |
| PHILIPS | N/A | 25P5 | CONVERGENCE WAY OFF IN THE CORNERS AND YOKE BUZZES | CHECK/REPLACE YOKE | |
| PHILIPS | N/A | 25P5 | VERTICAL BOUNCE/JUMP/JITTER/ROLL ON VCR PLAYBACK | CHANGE C682 TO ).22uF POLY (P/N# 483512147002) AND CHANGE R382 TO A 1mê (P/N# 483511057204) | |
| PHILIPS | N/A | 25P5 | CLOCK RUNS TOO FAST AND 'VOLUME LIMITER' FEATURE IS MISSING FROM THE MENU | REFER TO THE SERVICE MANUAL FOR PROCEDURES ON SETTING THE FEATURE WORD SETTING -- IT SHOULD BE SET TO 'HEX 25' | |
| PHILIPS | N/A | 25P5 | VERTICAL JITTER OR BOUNCE ON SOME CBALE CHANNELS | CHECK/REPLACE C682 WITH 0.22uF @ 100v (P/N# 483512147038) | |
| PHILIPS | N/A | 25P5 | TV WON'T SHUT OFF | CHECK/REPLACE Q400 (483513047072), Q402 (483513047059), D420 (483513037048),R431 (47 ), R432 (1K ), R437 (4.7 ) | |
| PHILIPS | N/A | 25P6 | VIDEO SMEARS ON BRIGHT OBJECTS | ADD 1meg (P/N# 483511657322) FROM PIN #52 OF IC270 TO GROUND | |
| PHILIPS | N/A | 25P6 | VERY SNOWY PICTURE AT 0dB SIGNAL LEVEL | CHECK/REPLACE R222 OPEN (12kê) (P/N# 483511657397) | |
| PHILIPS | N/A | 25P6 | CLOCK RUNS TOO FAST AND 'VOLUME LIMITER' FEATURE IS MISSING FROM THE MENU | REFER TO THE SERVICE MANUAL FOR PROCEDURES ON SETTING THE FEATURE WORD SETTING -- IT SHOULD BE SET TO 'HEX 25' | |
| PHILIPS | N/A | 25P6 | DEAD SET | CHECK FOR OPEN TRACE IN GRID 'H6' - ADD INSULATED WIRE FROM AC NUETRAL TO POINT MARKED PIN # 1 OF L400 | |
| PHILIPS | N/A | 25P6 | A SLIGHT VERTICAL DRIVE LINE MAY BE SEEN | INSTALL JUMPER AT B1 (GRID D2) | |
| PHILIPS | N/A | 25P6 | VERTICAL BOUNCE/JUMP/JITTER/ROLL ON VCR PLAYBACK | CHANGE C682 TO ).22uF POLY (P/N# 483512147002) AND CHANGE R382 TO A 1mê (P/N# 483511057204) | |
| PHILIPS | N/A | 25P6 | CONVERGENCE WAY OFF IN THE CORNERS AND YOKE BUZZES | CHECK/REPLACE YOKE | |
| PHILIPS | N/A | 25R5 | ERRATIC OPERATION - SELF ACTIVATION OF CHANNELS,ON/OFF, VOLUME - INTERMITTENT PROBLEM | CHECK/REPLACE KEYBOARD SWITCHES (LEAKY) (P/N# 483527657004) WHICH INCLUDES ALL 7 SWITCHES | |
| PHILIPS | N/A | 25R5 | PIP VIDEO HAS VERTICAL JITTER ON SOME CHANNELS | REMOVE C1036 AND SHORT WITH A JUMPER | |
| PHILIPS | N/A | 25R5 | PIP PICTURE JITTERS VERTICALLY | CHANGE C1028 WITH 0.047uF (P/N# 483512287503) | |
| PHILIPS | N/A | 25R5 | SOUND IMAGE CUTS IN/OUT ON MONO STATIONS - CUSTOMER COMPLAINS 'STEREO CUSTS OUT' | CHECK/REPLACE IC300 (P/N# 483520988462) | |
| PHILIPS | N/A | 25R5 | CONVERGENCE WAY OFF IN THE CORNERS AND YOKE BUZZES | CHECK/REPLACE YOKE | |
| PHILIPS | N/A | 25R5 | TOP OF PICTURE FOLDED OVER OR COMPRESSED AFTER SET IS WARM | CHECK/REPLACE YOKE (P/N# 483515017116) | |
| PHILIPS | N/A | 25R5 | OSD HAS WRONG LETTERS, WRONG SPELLING OR INCORRECT SPACING | CHECK/REPLACE IC300 (P/N# 483520988385) | |
| PHILIPS | N/A | 25R5 | LITTLE OR NO CLOSED CAPTION INFORMATION WHEN PLAYING BACK A RECORDED CABLE PROGRAM | CHANGE C682 TO 0.22uF POLY (P/N# 483513147002) AND CHANGE C358 TO 1uF (P/N# 483512147406) (NEG. TO IC300-#23) | |
| PHILIPS | N/A | 25R5 | ERRATIC RANDOM FUNCTIONS OR WRONG FUNCTIONS FOR BUTTONS PUSHED | CHECK/REPLACE FOR LEAKY KEYBOARD SWITCH (P/N# 483527657004) | |
| PHILIPS | N/A | 25R5 | BOUNCE IN THE PIP PICTURE | CHECK/REPLACE Y1002 (P/N# 483515397004) | |
| PHILIPS | N/A | 25R5 | VERTICAL BOUNCE/JUMP/JITTER/ROLL ON PREMIUM DECODED CABLE | CHANGE C682 TO 0.22uF POLY (P/N# 483512147002), ADD 1.2mê (P/N# 483511057204) FROM JUMPER B57 TO B40 | |
| PHILIPS | N/A | 25R5 | SOUND IS RASPY OR SLURRED OR HISSES WITH SOUND IMAGE TURNED ON AND STEREO TURNED ON | REMOVE C722 | |
| PHILIPS | N/A | 25R5 | LEFT AUDIO INPUT IS DEAD | SOUND IMAGE IS TURNED ON - THE RIGHT CHANNEL IS DESIGNED FOR MONO INPUT | |
| PHILIPS | N/A | 25R5 | VERTICAL JITTER ON SOME CABLE CHANNELS | CHECK/REPLACE C682 WITH 0.22uF @ 100v (P/N# 483512147038) DO NOT USE AN ELECTROLYTIC | |
| PHILIPS | N/A | 25R5 | TUNER SEARCHES IN THE CABLE MODE | CHECK/REPLACE C273 (0.01uF) (P/N# 483512247098) | |
| PHILIPS | N/A | 25S1 | WEAK VIDEO - WASHED VIDEO | CHECK/REPLACE Q210 | |
| PHILIPS | N/A | 25S1 | TEARING OR FLUTTERING LINES IN THE PICTURE AT LOW BRIGHTNESS | ADD A 6.8v ZENER ACROSS R676 WITH CATHODE TO 9v SOURCE - P/N# 483513037487 | |
| PHILIPS | N/A | 25S1 | LOSS OF MEMORY DUE TO GLITCHES IN THE RESET CIRCUIT | CHANGE R305 > 10 ohm, R416 > 2.2k, R417 > 10 ohm, R492 >> REMOVE, C411 > 22uF, D414 > 3.9v ZENER, Z410 > 5.6v ZENER | |
| PHILIPS | N/A | 25S1 | SET GOES INTO SHUTDOWN - MAY STAY ON WITH HORZ. LINES OR TEARING IN THE PICTURE | CHECK/REPLACE C432 (100uF @ 200v) | |
| PHILIPS | N/A | 25S1 | NO REMOTE CONTROL RESPONSE | CHECK/REPLACE IR RECEIVER (483521027003) | |
| PHILIPS | N/A | 25S1 | TEARING IN THE PICTURE AT VARIOUS BRIGHTNESS LEVELS | ADD 22k FROM PIN#40 OF IC265 TO GRD.,CHANGE C617 > 47uF, BRIGHTNESS REG.#11 MAY NEED TO BE RESET FOR BEST PERFORM. | |
| PHILIPS | N/A | 25S1 | DEAD SET | CHECK/REPLACE Q502 (483513047749),T501 (483514067051),AND F401 (483525397031) | |
| PHILIPS | N/A | 25S1 | OPERATION OF SET CAUSES INTERFERENCE ON NEAR BY AM RADIOS | CHECK/REPLACE ANTENNA ISOLATOR (P/N# 483521947173) | |
| PHILIPS | N/A | 25S1 | DEAD SET - F401 BLOWN AND AFTER REPLACING R432 BURNS | CHECK/REPLACE IC430 AND R432 (1K ) | |
| PHILIPS | N/A | 25S1 | NO TUNING ON CHANNELS 15-20 - ALL OTHERS OK | CHECK/REPLACE TUNER (483521047006) | |
| PHILIPS | N/A | 25S1 | SHORT VERTICAL SWEEP - ABOUT 2' | CHECK/REPLACE R565 FOR OPEN | |
| PHILIPS | N/A | 25S1 | DARK PICTURE OR NO PICTURE | CHECK/REPLACE C2 FOR SHORT ON CRT BOARD | |
| PHILIPS | N/A | 25S1 | FAILURE OF IC430 | CHECK/REPLACE IC430 AND Q400 FOR OPEN - ALSO CHECK THE SOLDER CONNECTIONS ON Q400 | |
| PHILIPS | N/A | 25S1 | DEAD SET OR MULTIPLE FAILURES OF R407 ****** THIS SET CANNOT BE RAN ON LOW AC ****** | CHECK/REPLACE R407 (483511687002) AND T502 (483514247015) | |
| PHILIPS | N/A | 25S1 | CANNOT TURN SET OFF | CHECK/REPLACE R438 (680k) FOR OPEN | |
| PHILIPS | N/A | 25S1 | NO SOUND BUT PIX IS NORMAL | CHECK/REPLACE IC230 | |
| PHILIPS | N/A | 25S1 | DEAD SET, POSSIBLY AFTER POWER SURGE | CHECK/REPLACE R403 (P/N# 483511247007),D401,D402,D403,D404 (P/N# FOR ALL 483513037059),R407 (P/N# 483511687002) | |
| PHILIPS | N/A | 25S1 | REPEATED OR EARLY FAILURE OF IC430 | CHECK/REPLACE Q400 | |
| PHILIPS | N/A | 25S1 | BRIGHT PICTURE WITH RETRACE LINES | CHECK/REPLACE Z410 AND Q410 | |
| PHILIPS | N/A | 25S1 | REPEATED SEARCHING IN THE CABLE MODE | CHANGE R241 TO A 680k (P/N 483511067143) | |
| PHILIPS | N/A | 25S1 | SHADING ON THE RIGHT SIDE OF THE PICTURE | CHECK/REPLACE C399 (P/N# 483512217002) - A FEW SETS WERE SENT OUT WITH A 1k RESISTOR IN PLACE OF THE CAPACITOR | |
| PHILIPS | N/A | 25S1 | OSD SHIFTED TOO FAR TO THE RIGHT | CHECK/REPLACE IC351 | |
| PHILIPS | N/A | 25S1 | R407 FAILS FOR NO APPARENT REASON AND Q403 MAY ALSO BE BAD | CHECK/REPLACE R407 (ONLY P/N 483511687002) - ADD 6.8k IN PARALLEL W/Z406 - CHNG. R502 TO 300 ohm-REPL. Z411 W/2.7k | |
| PHILIPS | N/A | 25S1 | NO PICTURE OR VERY DARK PICTURE - NO OSD | CHECK FOR CARBON PATH BETWEEN PINS #7 & #8 ON FLYBACK | |
| PHILIPS | N/A | 25S1 | OSD IS OFF CENTER - IT COULD BE SO FAR OFF CENTER THAT IT CAN'T BE SEEN | MOMENTARILY SHORT PINS 12 & 13 TO ENTER TEST MODE - PRESS RESET BUTTON TO GET TO REG.#10 - USE (+/-) TO CENTER | |
| PHILIPS | N/A | 25S1 | NO AUDIO OR INTERMITTENT AUDIO | CHECK/REPLACE Y220 OR COLD SOLDER CONNECTIONS | |
| PHILIPS | N/A | 25S1 | HUM OR AUDIO BUZZ OR DISTORTED AUDIO | CHECK TO SEE IF C464 IS A 100uF AND C465 IS A 1000pF ( THESE HAVE BEEN INTER-CHANGED ON SOME CHASSIS ) | |
| PHILIPS | N/A | 25S1 | TOTALLY DEAD | CHECK/REPLACE IC430 (STR30130) | |
| PHILIPS | N/A | 25S1 | NOISY BACKGROUND OR OVER PEAKED VIDEO | CHANGE R609 TO A 2.7k | |
| PHILIPS | N/A | 25S1 | DEAD SET - NO ATTEMPT TO START | CHECK/REPLACE R435 (130k ) FOR OPEN | |
| PHILIPS | N/A | 25S1 | NO HORZ. SWEEP - ONE VERTICAL WHITE LINE DOWN SCREEN | CHECK/REPLACE L507 FOR OPEN (P/N# 3620280021) | |
| PHILIPS | N/A | 25S1 | BLACK AND WHITE PIP MODULE FAILS TO OPERATE | CHANGE C21 TO 27pF (P/N# 483512287029) AND C23 TO 18pF (P/N# 483512287048) | |
| PHILIPS | N/A | 25S4 | OSD IS OFF CENTER - IT COULD BE SO FAR OFF CENTER THAT IT CAN'T BE SEEN | MOMENTARILY SHORT PINS 12 & 13 TO ENTER TEST MODE - PRESS RESET BUTTON TO GET TO REG.#10 - USE (+/-) TO CENTER | |
| PHILIPS | N/A | 25S4 | OPERATION OF SET CAUSES INTERFERENCE ON NEAR BY AM RADIOS | CHECK/REPLACE ANTENNA ISOLATOR (P/N# 483521947173) | |
| PHILIPS | N/A | 25S4 | TEARING OR FLUTTERING LINES IN THE PICTURE AT LOW BRIGHTNESS | ADD A 6.8v ZENER ACROSS R676 WITH CATHODE TO 9v SOURCE - P/N# 483513037487 | |
| PHILIPS | N/A | 25S4 | REPEATED OR EARLY FAILURE OF IC430 | CHECK/REPLACE Q400 | |
| PHILIPS | N/A | 25S4 | OSD SHIFTED TOO FAR TO THE RIGHT | CHECK/REPLACE IC351 | |
| PHILIPS | N/A | 25S4 | NO SOUND BUT PIX IS NORMAL | CHECK/REPLACE IC230 | |
| PHILIPS | N/A | 25S4 | DEAD SET - NO ATTEMPT TO START | CHECK/REPLACE R435 (130k ) FOR OPEN | |
| PHILIPS | N/A | 25S4 | LOSS OF MEMORY DUE TO GLITCHES IN THE RESET CIRCUIT | CHANGE R305 > 10 ohm, R416 > 2.2k, R417 > 10 ohm, R492 >> REMOVE, C411 > 22uF, D414 > 3.9v ZENER, Z410 > 5.6v ZENER | |
| PHILIPS | N/A | 25S4 | TOTALLY DEAD | CHECK/REPLACE IC430 (STR30130) | |
| PHILIPS | N/A | 25S4 | NO REMOTE CONTROL RESPONSE | CHECK/REPLACE IR RECEIVER (483521027003) | |
| PHILIPS | N/A | 25S4 | CANNOT TURN SET OFF | CHECK/REPLACE R438 (680k) FOR OPEN | |
| PHILIPS | N/A | 25S4 | NO PICTURE OR VERY DARK PICTURE - NO OSD | CHECK FOR CARBON PATH BETWEEN PINS #7 & #8 ON FLYBACK | |
| PHILIPS | N/A | 25S4 | BRIGHT PICTURE WITH RETRACE LINES | CHECK/REPLACE Z410 AND Q410 | |
| PHILIPS | N/A | 25S4 | BLACK AND WHITE PIP MODULE FAILS TO OPERATE | CHANGE C21 TO 27pF (P/N# 483512287029) AND C23 TO 18pF (P/N# 483512287048) | |
| PHILIPS | N/A | 25S4 | DEAD SET OR MULTIPLE FAILURES OF R407 ****** THIS SET CANNOT BE RAN ON LOW AC ****** | CHECK/REPLACE R407 (483511687002) AND T502 (483514247015) | |
| PHILIPS | N/A | 25S4 | TEARING IN THE PICTURE AT VARIOUS BRIGHTNESS LEVELS | ADD 22k FROM PIN#40 OF IC265 TO GRD.,CHANGE C617 > 47uF, BRIGHTNESS REG.#11 MAY NEED TO BE RESET FOR BEST PERFORM. | |
| PHILIPS | N/A | 25S4 | DEAD SET, POSSIBLY AFTER POWER SURGE | CHECK/REPLACE R403 (P/N# 483511247007),D401,D402,D403,D404 (P/N# FOR ALL 483513037059),R407 (P/N# 483511687002) | |
| PHILIPS | N/A | 25S4 | NO HORZ. SWEEP - ONE VERTICAL WHITE LINE DOWN SCREEN | CHECK/REPLACE L507 FOR OPEN (P/N# 3620280021) | |
| PHILIPS | N/A | 25T1 | NO VERTICAL SWEEP | CHECK/REPLACE R445 | |
| PHILIPS | N/A | 25T1 | BLACK AND WHITE PIP MODULE FAILS TO OPERATE | CHANGE C21 TO 27pF (P/N# 483512287029) AND C23 TO 18pF (P/N# 483512287048) | |
| PHILIPS | N/A | 25T1 | BRIGHT SCREEN WITH RETRACE LINES | CHECK/REPLACE R669 FOR OPEN | |
| PHILIPS | N/A | 25T1 | VERTICAL BOUNCE/JUMP/JITTER/ROLL ON VCR PLAYBACK | LOWER THE VALUE OF THE RESISTOR FROM PIN#28 OF IC200 TO GROUND - ONLY LOWER ENOUGH TO CORRECT (ORIGINAL VALUE 33kê) | |
| PHILIPS | N/A | 25T1 | DEAD SET OR INTERMITTENT | CHECK/REPLACE T501 OR MAY HAVE POOR CONNECTIONS | |
| PHILIPS | N/A | 25T1 | JAILBARS ON LEFT SIDE OF SCREEN | CHANGE L502 TO (P/N# 483515757673) AND L610 TO (P/N# 483515057038) NON-COMB MODELS ONLY | |
| PHILIPS | N/A | 25T1 | CLOCK RUNS TOO FAST OR LOSES TIME | CHANGE R388 TO A 16k 2 watt RESISTOR | |
| PHILIPS | N/A | 25T1 | DEAD SET - NO ATTEMPT TO TURN ON | CHECK/REPLACE Q502 (P/N# 2SD1555) | |
| PHILIPS | N/A | 25T1 | WHEN SET IS TURNED ON, Q501 SHORTS AND R504 OPENS | CHECK/REPLACE Q501,R504 AND T501 | |
| PHILIPS | N/A | 25T1 | INTERMITTENT DEAD SET OR SHUTS OFF AFTER WARM | CHECK/RESOLDER CONNECTIONS ON T501 | |
| PHILIPS | N/A | 25T1 | JAILBARS ON LEFT SIDE OF SCREEN | CHANGE L502 TO (P/N# 483515757673) AND L602 & L610 TO (P/N# 483515057004) COMB MODELS ONLY | |
| PHILIPS | N/A | 25T1 | DEAD SET OR LOCKED UP - REMOVING AC MAY CAUSE SET TO START | CHECK/REPLACE IC400 (P/N 483513097006) | |
| PHILIPS | N/A | 25T1 | REPEATED FAILURE OF Q501 | CHECK/REPLACE WITH CORRECT VALUE - SHOULD BE 1.8k,3watt P/N (483511667099) | |
| PHILIPS | N/A | 25T1 | NO PICTURE - HAS OSD AND SOUND - PICTURE MAY COME IN IF THE PIP BUTTON IS PRESSED ON REMOTE - SET DEFAULTS TO SPANISH | CHECK/REPLACE IC351 (P/N# 483520947113) | |
| PHILIPS | N/A | 25T1 | DISTORTED AUDIO OR STATIC IN THE AUDIO | CHECK/REPLACE R270 AND R271 | |
| PHILIPS | N/A | 25T1 | NO VERTICAL SWEEP | CHECK/REPLACE IC550 AND SMD R563 - ALSO VERIFY THAT C546 IS A .01uF @ 100V AND NOT A .1uF | |
| PHILIPS | N/A | 25T1 | NOISY PICTURE-OVER PEAKED-TOO SHARP | CHANGE R331 TO A 5.6k (483511137112) | |
| PHILIPS | N/A | 25T1 | AFTER CUSTOMER SETTINGS ARE SET (COLOR,TINT,LANGUAGE,ETC) AND POWER IS SHUT OFF OR SET UNPLUGGED, SETTINGS ALL CHANGE | CHECK/REPLACE IC351 (P/N# 483520988104) | |
| PHILIPS | N/A | 25U1 | DARK LINE TO THE LEFT OF THE COLOR PIP IMAGE RUNNING THE HEIGHT OF THE PIP BORDER | CHECK/REPLACE THE PIP MODULE | |
| PHILIPS | N/A | 25U6 | DEAD SET - NO HIGH VOLTAGE | CHECK/REPLACE Q500 (P/N# 483513047073) | |
| PHILIPS | N/A | 25V5 | HORZ. OFF FREQUENCY - MAY BE INTERMITTENT | CHECK/REPLACE Y620 (P/N# 483524277215) | |
| PHILIPS | N/A | 25V5 | 'SCREEN DOOR' EFFECT IN PICTURE DETAIL | CHECK/REPLACE Y600 COMB FILTER (P/N# 483515287002) | |
| PHILIPS | N/A | 25V5 | CANNOT DELETE CHANNELS FROM THE 'SMART SURF' ** RECORD ALL SERVICE MODE REGISTERS BEFORE REPL. PARTS ** | CHECK/REPLACE IC300 (P/N# 483520988488) AND IC302 (P/N# 483520988326)- RECORD ALL SERVICE SETTINGS 1ST | |
| PHILIPS | N/A | 25V5 | NO OSD - SET FUNCTIONS FINE OTHERWISE | CHECK/REPLACE L325 OR OPEN TRACE AT PINS# 18 & 19 OF IC300 | |
| PHILIPS | N/A | 25V5 | DEAD SET EXCEPT POWER LED | CHECK/REPLACE R538 | |
| PHILIPS | N/A | 25V5 | POOR VERTICAL SYNC.(ROLL,JITTER,BOUNCE) ON PREMIUM CHANNELS | CHANGE C682 TO 0.22uF POLY CAP (P/N# 483512147002) AND ADD 1.2mê FROM JUMPER B57 TO B40 | |
| PHILIPS | N/A | 25V5 | VOLUME LOSS W/CHANNEL CHANGE,SAP LOCKUP IN FRENCH MENU, SMART CLOCK OFF 1 HR. ** ONLY ON SETS WITH BLUE MENU BOX ** | CHECK/REPLACE MICROPROCESSOR (P/N# 483520988505) | |
| PHILIPS | N/A | 25V5 | INTERMITTENT CLOSED CAPTION OPERATION - DOUBLE SPACED LINES DROPOUTS OR COMPLETE LOSS. | C358 WAS INSTALLED IN REVERSE (P/N# 483512497175) | |
| PHILIPS | N/A | 25V5 | NARROW RASTER - LACKING WIDTH | CHECK/REPLACE C512 (P/N# 483512257004) (820pF) | |
| PHILIPS | N/A | 25W5 | BRIGHTNESS LEVEL VARIES BETWEEN THE TUNER SIGNAL AND THE VIDEO INPUTS | INSTALL R783 (75ê) (P/N# 483511137276) - MAY BE MISSING | |
| PHILIPS | N/A | 25W5 | INTERMITTENT CLOSED CAPTION OPERATION - DOUBLE SPACED LINES DROPOUTS OR COMPLETE LOSS. | C358 WAS INSTALLED IN REVERSE (P/N# 483512497175) | |
| PHILIPS | N/A | 25W5 | CANNOT DELETE CHANNELS FROM THE 'SMART SURF' ** RECORD ALL SERVICE MODE REGISTERS BEFORE REPL. PARTS ** | CHECK/REPLACE IC300 (P/N# 483520988488) AND IC302 (P/N# 483520988326)- RECORD ALL SERVICE SETTINGS 1ST | |
| PHILIPS | N/A | 25W5 | CLOSED CAPTION DROPS OUT OR HAS MISSPELLED WORDS | CHANGE C347 WITH SMD PART (1nF @ 50v) (P/N# 483512287023) | |
| PHILIPS | N/A | 25X1 | FOCUS DRIFTS AND MAY BE RETRACE LINES IN THE PICTURE | CHECK/RESOLDER CONNECTIONS ON THE GROUND PIN #15 ON FLYBACK | |
| PHILIPS | N/A | 25X1 | OSD CLOCK RUNS TOO FAST - GAINS 12 MINUTES AN HOUR - REMOVING POWER TEMPORARILY MAY RESTORE | CHANGE R326 TO 0 ohms (YES 0) (P/N#483511137019) AND R388 TO 16k 2 watt (P/N# 483511667087) | |
| PHILIPS | N/A | 25X1 | VERTICAL BOUNCE/JUMP/JITTER/ROLL ON VCR PLAYBACK | LOWER THE VALUE OF THE RESISTOR FROM PIN#28 OF IC200 TO GROUND - ONLY LOWER ENOUGH TO CORRECT (ORIGINAL VALUE 33kê) | |
| PHILIPS | N/A | 25X1 | THERE IS A REMOTE POSSIBILITY OF THE CUSTOMER SETTINGS MAY BE LOST AND SET MAY EXHIBIT NO COLOR,DARK PIX,ETC. | BRING UP 'PERSONAL PREFERANCE FACTORY SETTINGS' -- NO OTHER FIX EXIST FOR THIS PROBLEM | |
| PHILIPS | N/A | 25X1 | BLACK AND WHITE PIP MODULE FAILS TO OPERATE - SET WORKS FINE OTHERWISE - - Y2 ON PIP MODULE FAILS TO START | CHANGE C21 > 27pF (483512287029) AND C23 > (483512287048) | |
| PHILIPS | N/A | 25X1 | NO COLOR PIP FUNCTIONS | CHECK/REPLACE PIP MODULE (P/N# APP006A022) OR Y415 CRYSTAL WHICH IS THE PROBLEM (P/N# 483524277159) | |
| PHILIPS | N/A | 25X1 | CLOCK RUNS TOO FAST | CHANGE R326 TO 0 (P/N# 483511137019) AND R388 TO A 16k 2watt (P/N# 483511667087) | |
| PHILIPS | N/A | 25X1 | DEAD SET | CHECK/REPLACE R449 - CHANGE TO 27 ohm 1 watt (P/N# 483511657204) | |
| PHILIPS | N/A | 25X1 | REPEATED FAILURE OF D430A ( 130 VOLT RECTIFIER) | CHANGE TO (P/N# 483513037491) OR (P/N# 483513037114) OR (P/N# 483513037687) ONLY AND NOT ONE LISTED IN MANUAL | |
| PHILIPS | N/A | 25X1 | DEAD SET - NO ATTEMPT TO TURN ON | CHECK/REPLACE R449 WITH NEW PART (P/N# 483511657204) | |
| PHILIPS | N/A | 25X1 | WASHED OUT VIDEO ON SOME SCENES | CHECK/REPLACE R620 | |
| PHILIPS | N/A | 25X1 | WASHED OUT PICTURE AND WEAK VIDEO DRIVE | CHECK/REMOVE R620 IF (2) OF THEM EXIST. THERE SHOULD BE ONLY ONE RESISTOR AT THIS LOCATION | |
| PHILIPS | N/A | 25X6 | INTERMITTENT LOSS OF HORZ. SYNC | CHECK/REPLACE Y620 (P/N# 483524277215) | |
| PHILIPS | N/A | 25X6 | VERY SNOWY PICTURE AT 0dB SIGNAL LEVEL | CHECK/REPLACE R222 OPEN (12kê) (P/N# 483511657397) | |
| PHILIPS | N/A | 25X6 | DEAD SET | CHECK/REPLACE Q502 (P/N# 483513067001) AND F401 (P/N# 483525397031) | |
| PHILIPS | N/A | 25Y1 | POOR PICTURE | CHECK/REPLACE Z463 (P/N# 483513037121) | |
| PHILIPS | N/A | 25Y1 | DEAD SET OR WON'T SHUT OFF OR WON'T TUNE | CHECK/REPLACE IC345 | |
| PHILIPS | N/A | 25Y1 | NO CLOSED CAPTION | CHECK/REPLACE B10 AND B70 | |
| PHILIPS | N/A | 25Y1 | POOR CONTRAST AND BRIGHTNESS | CHECK/REPLACE Q510 (P/N# 483513047064), R468 (482211130483) | |
| PHILIPS | N/A | 25Y1 | FLAGGING AT TOP - POOR HORZ. SYNC. - 200v LINE INCREASED | CHECK/REPLACE D406 (P/N# 483513037048) | |
| PHILIPS | N/A | 25Y1 | NO AUDIO | CHECK/REPLACE Q95 (P/N# 483513047094), Q703 (483513047086), AND IC230 (P/N# 483520947005) | |
| PHILIPS | N/A | 25Y1 | NO SOUND - LOTS OF STATIC IN SOUND - LOW VOLUME | CHECK/RESOLDER CONNECTIONS ON IC270 AND L221 | |
| PHILIPS | N/A | 25Y1 | TUNER WILL NOT TUNE ANY CHANNELS | CHECK/REPLACE R360 AND R361 (P/N# 483511657275) | |
| PHILIPS | N/A | 25Y1 | CLOSED CAPTION IS MISSING FROM THE MENU AND IS TURNED ON | CHECK/RESOLDER CONNECTIONS ON B70 AND B10 | |
| PHILIPS | N/A | 25Y1 | CHANNEL NUMBERS CHANGE, BUT CHANNELS DON'T | CHECK/REPLACE PIP MODULE (P/N# 483521977517) | |
| PHILIPS | N/A | 25Y1 | HORZ. RUNNING OFF FREQUENCY | CHECK/REPLACE Z530 (P/N# 483513037121) | |
| PHILIPS | N/A | 25Y1 | TOTALLY DEAD | CHECK/REPLACE IC410 (STR30130) | |
| PHILIPS | N/A | 25Y1 | AM RADIO INTERFERENCE | CHECK/REPLACE ANTENNA ISOLATOR (P/N# 483521947173) | |
| PHILIPS | N/A | 25Y1 | HORIZONTAL OUTPUT FAILURE | CHECK/REPLACE C504 (483512147278) | |
| PHILIPS | N/A | 25Y1 | OSD SHIFTED | CHECK/REPLACE IC346 (P/N# 483520988108) | |
| PHILIPS | N/A | 25Y1 | DEAD SET - NO ATTEMPT TO START | CHECK/REPLACE Q502 (P/N# 483513047706) AND F401 (P/N# 483525397031) | |
| PHILIPS | N/A | 25Y1 | DEAD SET - NO ATTEMPT TO START | CHECK/REPLACE Q502 (P/N# 483513047706) AND F401 (P/N# 483525397031) | |
| PHILIPS | N/A | 25Y1 | DEAD SET - NO ATTEMPT TO START | CHECK/REPLACE Q402 (P/N# ECG382) | |
| PHILIPS | N/A | 25Y1 | DISTORTED AUDIO OR NO AUDIO | CHECK/REPLACE L221 (P/N# 483515757113) | |
| PHILIPS | N/A | 25Y1 | NO SAP | ADD 270K (P/N# 483511067116) TO PIN #1 OF IC700 TO GRD. | |
| PHILIPS | N/A | 25Y1 | NO VIDEO OR OSD | CHECK/REPLACE L630 (P/N# 483515757947),D508 (483513037048) L340 (P/N# 483515757141), R6 (483511657318 - CRT BOARD) | |
| PHILIPS | N/A | 25Y1 | VERTICAL OUTPUT FAILURE | CHECK/REPLACE IC550 AND C447 (P/N# 483512447013) | |
| PHILIPS | N/A | 25Y1 | HORZ. IS OFF FREQUENCY | CHECK/REPLACE IC410 (P/N# 483520947056) | |
| PHILIPS | N/A | 25Y1 | SET GOES INTO SHUTDOWN - MAY STAY ON WITH HORZ. LINES OR TEARING IN THE PICTURE | CHECK/REPLACE C432 (100uF @ 200v) | |
| PHILIPS | N/A | 25Y1 | NO VERTICAL SWEEP - POSSIBLY REPEATED FAILURE | CHECK/REPLACE D445 (P/N# ECG552) ,R445 (1 1/2w.) AND IC550 (P/N# LA7831) | |
| PHILIPS | N/A | 25Y1 | NO VIDEO OR POOR CONTRAST | CHECK/REPLACE C511 (P/N# 483512247224), R538 (483511657427) | |
| PHILIPS | N/A | 25Y1 | DEAD SET | CHECK/REPLACE Z402 (P/N# 483513037003), Z406 (483513037121) | |
| PHILIPS | N/A | 25Y1 | SET WILL NOT TURN ON/OFF | CHECK IC410 (P/N# 483520947056), Q400 (483513047072), R438 (P/N# 483511657518), R432 (P/N# 483511657108) | |
| PHILIPS | N/A | 25Y1 | NO VIDEO | CHECK PIP MODULE (483521977517),C301(483512497026),Q210 (483513047126),Q602 (483513047064), R243 (483511657322) | |
| PHILIPS | N/A | 25Y1 | REMOTE WILL RESPOND TO REMOTES FOR OTHER PRODUCTS SUCH AS AUDIO,VCR, ETC. | CHECK/REPLACE IC350 WITH NEW TYPE (P/N# 483520988286) | |
| PHILIPS | N/A | 25Y1 | SHORT VERTICAL SWEEP OR FOLDOVER | CHECK/REPLACE Q560 (P/N# 483513047064) AND R552 (P/N# 483511657322) | |
| PHILIPS | N/A | 25Y1 | WON'T SHUT OFF - COMES ON WHEN PLUGGED IN | CHECK/REPLACE R438 (680k 1/2w) | |
| PHILIPS | N/A | 25Y4 | NO SOUND - LOTS OF STATIC IN SOUND - LOW VOLUME | CHECK/RESOLDER CONNECTIONS ON IC270 AND L221 | |
| PHILIPS | N/A | 25Y4 | NO VERTICAL SWEEP - POSSIBLY REPEATED FAILURE | CHECK/REPLACE D445 (P/N# ECG552) ,R445 (1 1/2w.) AND IC550 (P/N# LA7831) | |
| PHILIPS | N/A | 25Y4 | DEAD SET OR WON'T SHUT OFF OR WON'T TUNE | CHECK/REPLACE IC345 | |
| PHILIPS | N/A | 25Y4 | SET WILL NOT SHUT OFF | CHECK/REPLACE Q400 (P/N# TIP47) | |
| PHILIPS | N/A | 25Z1 | VERTICAL BOUNCE/JUMP/JITTER/ROLL ON VCR PLAYBACK | LOWER THE VALUE OF THE RESISTOR FROM PIN#28 OF IC200 TO GROUND - ONLY LOWER ENOUGH TO CORRECT (ORIGINAL VALUE 33kê) | |
| PHILIPS | N/A | 25Z1 | REMOTE WILL RESPOND TO REMOTES FOR OTHER PRODUCTS SUCH AS AUDIO,VCR, ETC. | CHECK/REPLACE IC300 WITH NEW TYPE (P/N# 483520988286) | |
| PHILIPS | N/A | 26B1 | NO HORIZONTAL SYNC. | REPLACED R247 OFF PIN 43 OF IC250 | |
| PHILIPS | N/A | 26B1 | DISTORTED AUDIO--OUTPUTS ARE OK | CHECK R210 -- ESPECIALLY IF OUTPUT XSTRS. WERE BAD | |
| PHILIPS | N/A | 26B1 | NO SOUND AND NO RASTER -IC250 LATCHES UP | REPLACE Q370 AND IC250 | |
| PHILIPS | N/A | 26B1 | NO PICTURE,NO COLOR AND NO RASTER | CHECK/REPLACE Q516 (P/N# 6104359001) | |
| PHILIPS | N/A | 26B1 | DEAD SET OR SHUTS DOWN | CHECK/REPLACE D530 OR Z530 | |
| PHILIPS | N/A | 26B1 | DEAD SET-MAY BE INTERMITTENT | CHECK CONNECTIONS ON R335 | |
| PHILIPS | N/A | 26B1 | NO COLOR | CHECK/REPLACE R516 OPEN | |
| PHILIPS | N/A | 26B1 | INTERMITTENT SHUTDOWN OR VERT. SWEEP | REPLACE Z670 (LEAKY) | |
| PHILIPS | N/A | 26B1 | VERTICAL FOLDOVER AFTER SET WARMS UP | CHECK/REPLACE D554 (P/N# 5302991001) | |
| PHILIPS | N/A | 26B1 | PICTURE PULSATING FROM PIX TO SNOW | REPLACED R409 | |
| PHILIPS | N/A | 26B1 | POOR OR SNOWY RECEPTION | CHECK/REPLACE Q220 AND Q311 WITH (P/N# 610434004) | |
| PHILIPS | N/A | 26B1 | CHANNELS HIGHER THAN 7 CANNOT BE SELECTED | CHECK/REPLACE XT309 | |
| PHILIPS | N/A | 26B1 | DEAD SET TICKING SOUND | REPAIRED BROKEN SOLDER CONNECTION ON R335 | |
| PHILIPS | N/A | 26B1 | NO PICTURE - NO SOUND AND NO RASTER | CHECK/REPLACE Q370 | |
| PHILIPS | N/A | 26B1 | AUDIO DISTORED AND HAS A BUZZING NOISE VOL.NOT W | REPLACED LEAKY VOLUME CONTROL AMP,Q370 | |
| PHILIPS | N/A | 26B1 | SET WOULD NOT LOCK ON STATION | REPLACED Y301 | |
| PHILIPS | N/A | 26B1 | SLOW VERTICAL ROLL - VETTICAL WON'T LOCK | CHECK/REPLACE R237 | |
| PHILIPS | N/A | 26B1 | EXCESSIVE B+ - 130V SOURCE TOO HIGH | CHECK/REPLACE R409 | |
| PHILIPS | N/A | 26B1 | SET WAS DEAD OUT-OF-BOX IN CUSTOMERS HOME | REPLACED OPEN R409 | |
| PHILIPS | N/A | 26B1 | TUNER HUNTS ON CHANNEL CHANGES 4 TIMES - AFT PROBLEMS | CHECK R342 FOR INCREASE IN VALUE | |
| PHILIPS | N/A | 26B1 | TUNER SEARCHES - POOR AFT LOCK | CHECK/REPLACE IC250 - CHECK ALIGNMENT OF L243 | |
| PHILIPS | N/A | 26B1 | INTERMITTENT SHUTDOWN | CHECK/REPLACE Q690 AND Z689 | |
| PHILIPS | N/A | 26B1 | DEAD SET | REPLACED IC400 | |
| PHILIPS | N/A | 26B1 | INTERMITTENT SHUTDOWN OR LOSS OF VERTICAL SWEEP | CHECK/REPLACE Z670 (P/N# 5301571270) | |
| PHILIPS | N/A | 26B1 | VERTICAL LINE ON THE LEFT SIDE OF THE SCREEN | INSTALL A FERRITE BEAD ON EMITTER OF Q503 (HORZ DRVR) | |
| PHILIPS | N/A | 26B1 | AUDIO OUTPUT FAILURES---REPL.C211 1uF C206 470pF | PARALLEL 470pF @ R202 R207 10 OHM R213&R214 130 OHM | |
| PHILIPS | N/A | 26B1 | POP OR CHIRP IN THE AUDIO AT TURN OFF | CHECK FOR A 0.1uF AT PIN #6 OF IC (COUPLING CAP.) | |
| PHILIPS | N/A | 26C5 | DEAD SET WITH POWER SUPPLY SQUEALING WHEN SET IS TURNED ON | CHECK/REPLACE D404 FOR SHORT | |
| PHILIPS | N/A | 26C5 | NO SOUND OR PIX | CHECK D461 FOR LEAKAGE (MAY CHECK GOOD FRONT TO BACK) | |
| PHILIPS | N/A | 26C5 | DELAYS LOCKING ONTO CHANNEL AND LOOKS LIKE TUNER | CHECK/REPLACE IC340 (ALSO CHECK FOR COINCIDENCE PULSE AT PIN #13 OF IC340) | |
| PHILIPS | N/A | 26C5 | DEAD SET-NO REGULATOR B+ | CHECK IC340 FOR SQR.WAVE AT PIN #11-REPL. IF MISSING | |
| PHILIPS | N/A | 26C5 | SET SHUTS OFF WITH AC BELOW 110 VOLTS | CHECK/REPLACE C458 | |
| PHILIPS | N/A | 26C5 | NO SOUND AND POOR PICTURE - APPEARS TO HAVE ARCING IN THE PICTURE | CHECK/REPLACE D408 AND R408 | |
| PHILIPS | N/A | 26C5 | HUM BAR BUT WITHOUT SHADING - WORSE AT HIGH BRIGHTNESS | CHECK/REPLACE D425 FOR LEAKAGE | |
| PHILIPS | N/A | 26C5 | NO COLOR OR NO COLOR SYNC | CHECK/REPLACE IC150,Y194,SF38,C182,C185,C174,Q35,C180 | |
| PHILIPS | N/A | 26C5 | NO VERTICAL SYNC | CHECK/REPLACE IC340 | |
| PHILIPS | N/A | 26C5 | NO HORZ.SYNC | CHECK/REPLACE R50 AND L405 | |
| PHILIPS | N/A | 26C5 | NO VIDEO | CHECK/REPLACE IC331,IC340,IC51,Q158,R408,R414,R410 | |
| PHILIPS | N/A | 26C5 | NO START UP VOLTAGE | D461 OPEN OR LEAKY | |
| PHILIPS | N/A | 26C5 | B+ ABOUT 100V-WILL ADJUST BUT NOT TO 130V | CHECK D581 (5.6V ZENER) FOR LEAKAGE | |
| PHILIPS | N/A | 26C5 | NO VIDEO OR BRIGHT. UNLESS MASTER SCRN. RAISED | CHECK C425 | |
| PHILIPS | N/A | 26C5 | ARCING IN THE PICTURE OR POOR FOCUS | CHECK/REPLACE R255 AND T408 | |
| PHILIPS | N/A | 26C5 | HORIZONTAL BENDING | CHECK/REPLACE D425 | |
| PHILIPS | N/A | 26C5 | RETRACE LINES IN THE PICTURE | CHECK/REPLACE IC150,Q226,Q240 | |
| PHILIPS | N/A | 26C5 | NO BLUE | CHECK/REPLACE R245,R233,IC150 | |
| PHILIPS | N/A | 26C5 | SHORT VERTICAL SWEEP | CHECK/REPLACE R420 (MAY CHECK GOOD OUT OF CIRCUIT) | |
| PHILIPS | N/A | 26C5 | DARK SCREEN-NO VIDEO--SOUND AND HIGH VOLTS OK | CHECK C425 | |
| PHILIPS | N/A | 26C5 | SET SHUTS DOWN ON LOW AC LINE VOLTAGE | CHECK/REPLACE C458 | |
| PHILIPS | N/A | 26C5 | DEAD SET (USUALLY AFTER A STORM) | CHECK/REPLACE IC1000 | |
| PHILIPS | N/A | 26C5 | RINGING IN THE PIX | CHECK/REPLACE Q156,Y151,Z481,SF38 | |
| PHILIPS | N/A | 26C5 | VERY LITTLE SOUND AND NO PICTURE-BRIGHT RASTER W/RETRACE | CHECK/REPLACE D408 AND R408 | |
| PHILIPS | N/A | 26C5 | NO RED OR HAS RED RASTER | CHECK/REPLACE IC150 | |
| PHILIPS | N/A | 26C5 | DEAD SET | CHECK/REPLACE Q401,Q464,T408,T453,IC340,IC331,C338,C470, D404,D461,D459,IC469,Q463,Q457,Z481,Q470,Q471,Q494,R339 | |
| PHILIPS | N/A | 26C5 | VERTICAL FOLDOVER,JITTER OR NO SWEEP | CHECK/REPLACE C321,Z481,IC331,IC340,R420,D420C322,L414,R328 | |
| PHILIPS | N/A | 26C5 | NO RASTER OR SOUND BUT B+ IS NORMAL AND HORZ. HEATSINK RUNNING VERY HOT. | CHECK/REPLACE DEFLECTION YOKE | |
| PHILIPS | N/A | 26C6 | FINE HORZ. LINES IN PICTURE | CHECK/REPLACE PINCUSHION MODULE | |
| PHILIPS | N/A | 26C6 | HUM IN AUDIO | CHECK D170 | |
| PHILIPS | N/A | 26C6 | Q501 OVERHEATS/SHORTS--APPEARS FLYBACK SHORTED | CHECK R503 (47 OHM) FOR OPEN OR HIGH RESISTANCE | |
| PHILIPS | N/A | 26C6 | DEAD SET-NO REGULATED B+ | CHECK IC340 FOR SQR WAVE AT PIN #11-REPL. IF MISSING | |
| PHILIPS | N/A | 26C6 | NO RASTER | DEFECTIVE CRT | |
| PHILIPS | N/A | 26C6 | VOLUME AND CHANNELS CHANGE BY THEMSELVES | REPLACE 4.0MHz CRYSTAL | |
| PHILIPS | N/A | 26C6 | DEAD SET-GRD. BASE OF Q402 AND SET COMES ON | CHECK/REPLACE IC403 | |
| PHILIPS | N/A | 26C6 | NO HIGH VOLTAGE | CHECK/REPLACE D461,Q464,Q463,T465,T460,IC320,R434,R435, R337,R464,R428,Q461,D462 | |
| PHILIPS | N/A | 26C6 | RETRACE LINES IN PIX | CHECK/REPLACE C303,R56,IC50,IC320,IC300,Q11,Q31,Q51 | |
| PHILIPS | N/A | 26C6 | DISTORTED VERTICAL AT TOP AND BOTTOM | CHECK/REPLACE RESISTOR LOCATED ON THE ANODE SIDE OF D1 ON THE PINCUSHION MODULE. | |
| PHILIPS | N/A | 26C6 | INTERMITTENT OR COMPLETE SHUTDOWN | CHECK/RESOLDER CONNECTIONS ON C550 | |
| PHILIPS | N/A | 26C6 | DEAD SET | CHECK C466 AND IC1200 | |
| PHILIPS | N/A | 26C6 | PICTURE OVER SCANS VERTICALLY AND HORIZONTALLY | CHECK Q464 FOR SHORTS -- ESPECIALLY IF SAFTEY CAP. | |
| PHILIPS | N/A | 26C6 | MISSING ONE COLORS | CHECK/REPLACE IC50,Q11,Q31,Q51 | |
| PHILIPS | N/A | 26C6 | DEAD SET OR INTERMITTENT POWER | CHECK T400 CONNECTIONS | |
| PHILIPS | N/A | 26C6 | DEAD SET | CHECK Q321 AND Z370 | |
| PHILIPS | N/A | 26C6 | NO HIGH VOLTAGE BUT DOES HAVE SOUND | CHECK/RESOLDER CONNECTIONS ON Q462 | |
| PHILIPS | N/A | 26C6 | DEAD SET | CHECK/REPLACE Q400,D400,D401,D402,D403,Q401,R420,R408, IC403,D430,Z407,R402,R403,C411,Z436,R431 | |
| PHILIPS | N/A | 26C6 | DEAD SET | CHECK R434 AND D433 | |
| PHILIPS | N/A | 26C6 | JAPANESE CHARACTERS AFTER REPLACING IC1200 | CHECK/REPLACE IC1200 - MAKE SURE NUMBER ON IC IS MN1277B | |
| PHILIPS | N/A | 26C6 | ON MODELS WITH 10 WATT AMP, A LOUD THUMP IS HEARD WHEN TURNING SET ON. | CHECK/REPLACE D170 AND CHANGE C163 FROM 330uF TO 1000uF | |
| PHILIPS | N/A | 26C6 | NO COLOR | CHECK/REPLACE IC50,Y50,IC10,R50,R435,C66,IC320,R56 | |
| PHILIPS | N/A | 26C6 | NO VIDEO | CHECK/REPLACE IC601,R434,R435,IC50,Q54,IC10,R56 | |
| PHILIPS | N/A | 26C6 | ARCING IN CRT OR IN VIDEO | CHECK/REPLACE T465 | |
| PHILIPS | N/A | 26C8 | PICTURE SIZE VARIES BOTH HORZ. AND VERT. | CHECK/REPLACE C421 | |
| PHILIPS | N/A | 26C8 | BLANK RASTER OR SLICK RASTER-SOUND OK | CHECK/REPLACE IC580 (VERT.OUTPUT IC) | |
| PHILIPS | N/A | 26C8 | BRIGHT SCREEN WITH NO VIDEO - OSD LOOKS LIKE THE HORZ. PHASE IS OFF AS GRAPHICS ARE SHIFTED | CHECK/REPLACE R501 OR R502 FOR OPEN | |
| PHILIPS | N/A | 26C8 | POOR SOUND FROM LEFT SPEAKER WITH EXPANDED SOUND SWITCH ON. | CHECK/REPLACE IC400 ON THE STEREO DECODER BOARD. | |
| PHILIPS | N/A | 26C8 | NO STANDBY VOLTAGES OR LOW STANDBY VOLTAGE OR 130V TOO HIGH | CHECK/REPLACE D414,D416,Q406 AND Q407 | |
| PHILIPS | N/A | 26C8 | POOR AFT LOCK - ADJUSTING AFT DETECTOR HELPS BUT DOESN'T COMPLETELY CORRECT | CHECK/REPLACE Y200 SAW FILTER (P/N# 483515497068) | |
| PHILIPS | N/A | 26C8 | DARK PIX ON LEFT SIDE | CHECK C508 | |
| PHILIPS | N/A | 26C8 | PICTURE IS SHIFTED 8 TO 10 INCHES TO THE RIGHT - HORZ. BLANKING BAR IS IN THE CENTER OF THE SCREEN | CHECK/REPLACE R501 AND R502 FOR OPEN | |
| PHILIPS | N/A | 26C8 | BRIGHT RASTER WITH RETRACE AND DIM VIDEO | CHECK/REPLACE R25 (CRT BOARD) | |
| PHILIPS | N/A | 26C8 | DEAD SET | CHECK/REPLACE Q406 | |
| PHILIPS | N/A | 26C8 | INTERMITTENT LOSS OF HORZ. HOLD AND PIX SHRINKS HORZ. | CHECK R505 FOR CONNECTIONS PROBLEMS | |
| PHILIPS | N/A | 26C8 | DEAD SET | CHECK R434 FOR OPEN | |
| PHILIPS | N/A | 26C8 | SHUTDOWN,130V NOT REGULATING OR NOT HIGH ENOUGH | CHECK IC201,IC580,Q400,SCR401,Q402,Q403,Q406,Q407, | |
| PHILIPS | N/A | 26C8 | BRIGHT SCREEN W/RETRACE - SHORT VERT. - AUDIO IS NORMAL | CHECK R510 FOR OPEN | |
| PHILIPS | N/A | 26C8 | DEAD SET | CHECK/REPLACE D414,D416,Q406 AND Q407 | |
| PHILIPS | N/A | 26C8 | HERRINGBONE,VERT.JITTER,INT.COLOR,DOUBLE IMAGE | CHECK/REPLACE IC201 | |
| PHILIPS | N/A | 26C8 | INTERMITTENT PIX-BLACKS OUT-AUDIO LEVEL DROPS | CHECK ALL CONNECTIONS ON T500 | |
| PHILIPS | N/A | 26C8 | STANDBY VOLTAGE IS TOO HIGH (22VDC) AND FULL POWER IS SLIGHTLY HIGH (132VDC) BUT NO HIGH VOLTAGE. | CHECK/REPLACE Q500 | |
| PHILIPS | N/A | 26C8 | PIX BREAKS UP,BLOOMS,AND VERT SIZE DECREASES | CHECK Q406,Q407 AND Z436 FOR SHORTS | |
| PHILIPS | N/A | 26C8 | INTERMITTENT SOUND OR FULL VOLUME WITH NO CONTROL | CHECK/RESOLDER ALL CONNECTIONS ON THE BOTTOM OF THE 'IF' CAGE TO THE PCB. | |
| PHILIPS | N/A | 26C8 | Q501 OVERHEATS/SHORTS--APPEARS FLYBACK SHORTED | CHECK R503 (47 OHM) FOR OPEN OR HIGH RESISTANCE | |
| PHILIPS | N/A | 26C8 | NO SOUND - AFTER REPLACING IC280 IT RUNS VERY WARM | CHECK/REPLACE IC280,R284 AND C287 | |
| PHILIPS | N/A | 26C8 | DEAD SET AFTER INSTALLATION OF IC404 | CHECK FOR PROPER ORIENTATION OF IC404 - SOME BOARDS WERE MARKED WRONG WITH RESPECT TO PIN#1 OF THE IC. | |
| PHILIPS | N/A | 26C8 | TUNER SEARCHES AFTER CHANNEL IS SELECTED | RESOLDER IC309 | |
| PHILIPS | N/A | 26C8 | DEAD SET-NO REG B+ | CHECK IC340 FOR SQR. WAVE @ PIN #11--IF MISSING REPL. | |
| PHILIPS | N/A | 26C8 | NO VIDEO OR LUMINANCE | CHECK/REPLACE LEAKY HORZ.DRIVER XSTR. | |
| PHILIPS | N/A | 26C8 | WHEN BRIGHTNESS INCREASES,PIX SHRINKS VERTICALLY | CHECK D416 FOR OPEN (OUT OF CIRCUIT) | |
| PHILIPS | N/A | 26C8 | POOR SOUND FROM LEFT SPKR WITH SOUND EXPAND ON | REPLACE IC400 ON THE SAP BOARD | |
| PHILIPS | N/A | 26C8 | NO PIX-RASTER AND SOUND OK | CHECK C642 SHORTED | |
| PHILIPS | N/A | 26C8 | DEAD SET BUT POWER LED COMES ON WHEN POWER BUTTON IS PUSHED | CHECK/REPLACE Z408 FOR SHORT | |
| PHILIPS | N/A | 26C8 | WONT SHUT OFF AND VOLUME AT MAXIMUN LEVEL | REPLACED R430 | |
| PHILIPS | N/A | 26C8 | NO VOLUME CTRL.--DOESN'T MUTE ON CHANNEL CHANGE | CHECK IC280 | |
| PHILIPS | N/A | 26C8 | DEAD SET--NO HORZ. DRIVE | CHECK Q500 | |
| PHILIPS | N/A | 26C8 | DEAD SET-POWER SUPPLY IS OK-NO HORZ. DRIVE | CHECK IC201 AND Q500 | |
| PHILIPS | N/A | 26C8 | WHITE SMOOTH RASTER (NO VIDEO) - SOUND OK | CHECK/REPLACE C631 AND IC640 | |
| PHILIPS | N/A | 26C8 | DEAD SET - STANDBY VOLTAGE IS TOO HIGH AND FULL POWER IS SLIGHTLY HIGH (132 VOLTS) | CHECK/REPLACE Q500 | |
| PHILIPS | N/A | 26C8 | DEAD SET | CHECK/REPLACE T500 (HORZ. DRIVER XFRM) | |
| PHILIPS | N/A | 26C8 | PIX SHIFTED TO RIGHT,4' BLACK BAR ON LEFT SIDE | CHECK R508 FOR BREAKING DOWN UNDER LOAD | |
| PHILIPS | N/A | 26C8 | NO VIDEO WITH RETRACE LINES | CHECK D500 FOR LEAKAGE (WILL CHECK GOOD) | |
| PHILIPS | N/A | 26C8 | FULL VOLUME-VOL.CHNG. CAUSES TUNER TO SEARCH | CHECK IC280 | |
| PHILIPS | N/A | 26C8 | NO STANDBY VOLTAGES | REPLACED R407/INDUCTOR L402 | |
| PHILIPS | N/A | 26C8 | DEAD SET - PIN#26 OF IC201 IS SHORTED TO GROUND. | CHECK/REPLACE Z436 | |
| PHILIPS | N/A | 26C8 | GARBLED SOUND AND POSSIBLY ONLY ON CERTAIN CHANNELS | CHECK/REPLACE Y201 SAW FILTER (P/N 483515497069) | |
| PHILIPS | N/A | 26C8 | INTERMITTENT BRIGHTNESS VARIATIONS | CHECK/REPLACE R25 ON CRT BOARD | |
| PHILIPS | N/A | 26C8 | SHORT VERTICAL SWEEP | CHECK/REPLACE R239 (10megê) | |
| PHILIPS | N/A | 26C8 | STANDBY AND FULL POWER VOLTAGES TOO LOW | CHECK/REPLACE Z436 FOR SHORT | |
| PHILIPS | N/A | 26C8 | STANDBY VOLTAGE AT TP4 OK BUT THE FULL POWER 130VDC IS TOO LOW (29VDC) | CHECK/REPLACE Q406 | |
| PHILIPS | N/A | 26C9 | POWER LIGHT COMES ON BUT SET IS DEAD | CHECK/REPLACE Z408 | |
| PHILIPS | N/A | 26C9 | DEAD SET-NO REGULATED B+ | CHECK IC340 FOR SQR WAVE AT PIN #11-REPL. IF MISSING | |
| PHILIPS | N/A | 26C9 | NO SOUND,COLOR OR BRIGHTNESS - ONLY DIM VIDEO | CHECK/REPLACE IC312 | |
| PHILIPS | N/A | 26C9 | SHORT VERTICAL SWEEP | CHECK/REPLACE R239 (10megê) | |
| PHILIPS | N/A | 26C9 | TUNING SYSTEM LOCKS UP | REPLACE THE TUNER | |
| PHILIPS | N/A | 26C9 | NO RASTER OR SOUND | REPLACE IC312 | |
| PHILIPS | N/A | 26C9 | PIX AND AUDIO LEVELS VARY | CHECK ALL CONNECTIONS ON T401 | |
| PHILIPS | N/A | 26C9 | VERTICAL JITTER ON VCR OR NON STANDARD SIGNAL | SEE SERVICE BULLETIN MARCH/APRIL 1988 ISSUE 2 | |
| PHILIPS | N/A | 26C9 | EXCESSIVE BRIGHTNESS,SHUTSDOWN-LOOKS LIKE VERT. COLLAPSE | CHECK R680 -MUST BE CHECKED OUT OF CIRCUIT | |
| PHILIPS | N/A | 26C9 | NO RASTER OR SOUND--HIGH VOLTAGE OK | CHECK IC312 | |
| PHILIPS | N/A | 26C9 | DEAD SET | CHECK R424 ALSO VARACTOR TUNER | |
| PHILIPS | N/A | 26C9 | COMPRESSED VERT SWEEP AFTER SET IS WARM | REPLACE THE DEFLECTION YOKE | |
| PHILIPS | N/A | 26C9 | POOR PICTURE RECEPTION | CHECK/REPLACE Y200 (SAW FILTER) | |
| PHILIPS | N/A | 26C9 | LOSS OF HORIZONTAL SYNC. AND LOSS OF COLOR AFTER 5-10 MINS. | CHECK/REPLACE IC201 (TDA4505A) | |
| PHILIPS | N/A | 26C9 | DEAD SET AND POWER SUPPLY VOLTAGES ON THE SECONDARY WERE ABOUT 70% OF THE NORMAL VALUE. | CHECK/REPLACE Z408 (CHANGE IN VALUE) | |
| PHILIPS | N/A | 26C9 | COMES ON BUT PIX DIM-NO COLOR-NO O.S.D. | REPLACE IC312 | |
| PHILIPS | N/A | 26C9 | PICTURE IS SHIFTED 8 TO 10 INCHES TO THE RIGHT - HORZ. BLANKING BAR IS IN THE CENTER OF THE SCREEN | CHECK/REPLACE R501 AND R502 FOR OPEN | |
| PHILIPS | N/A | 26C9 | NO SOUND | CHECK L212 | |
| PHILIPS | N/A | 26C9 | DEAD SET BUT POWER LED COMES ON WHEN POWER BUTTON IS PUSHED | CHECK/REPLACE Z408 FOR SHORT | |
| PHILIPS | N/A | 26C9 | LOSES COLOR PURITY INTERMITTENTLY | CHECK/REPLACE INTERMITTENT T401 | |
| PHILIPS | N/A | 26C9 | GARBLED SOUND AND POSSIBLY ONLY ON CERTAIN CHANNELS | CHECK/REPLACE Y201 SAW FILTER (P/N 483515497069) | |
| PHILIPS | N/A | 26C9 | INTERMITTENT DEAD SET OR SET GOES OFF | CHECK CONNECTIONS ON T401 | |
| PHILIPS | N/A | 26C9 | DEAD SET OR SET GOING INTO SHUTDOWN | CHECK VALUE OF R424 | |
| PHILIPS | N/A | 26C9 | SHUTS DOWN WHILE CHANGING CHANNELS | REPLACE Z503 AND Z504 | |
| PHILIPS | N/A | 26C9 | BRIGHT SCREEN WITH NO VIDEO - OSD LOOKS LIKE THE HORZ. PHASE IS OFF AS GRAPHICS ARE SHIFTED | CHECK/REPLACE R501 OR R502 FOR OPEN | |
| PHILIPS | N/A | 26C9 | AUDIO DISTORTION AT LOW VOL. OR MUTED | REPLACE IC501 | |
| PHILIPS | N/A | 26C9 | POOR AFT LOCK - ADJUSTING AFT DETECTOR HELPS BUT DOESN'T COMPLETELY CORRECT | CHECK/REPLACE Y200 SAW FILTER (P/N# 483515497068) | |
| PHILIPS | N/A | 26D5 | INTERMITTENT OR MISSING ONE PRIMARY COLOR | CHECK/REPLACE Q21,Q22 OR Q23 ON CRT BOARD - MAY BE LABELED AS Q1,Q2,Q3 (P/N# 483513047059) | |
| PHILIPS | N/A | 26D6 | INTERMITTENT OR MISSING ONE PRIMARY COLOR | CHECK/REPLACE Q21,Q22 OR Q23 ON CRT BOARD - MAY BE LABELED AS Q1,Q2,Q3 (P/N# 483513047059) | |
| PHILIPS | N/A | 26G1 | POP OR CHIRP IN THE AUDIO AT TURN OFF | CHECK FOR A 0.1uF AT PIN #6 OF IC (COUPLING CAP.) | |
| PHILIPS | N/A | 26G1 | TV CYCLING ON AND OFF | CHECK FOR SHORTED VERTICAL OUTPUT IC LOADING DOWN | |
| PHILIPS | N/A | 26G1 | HORZ. WAVE FLOATING THROUGH PICTURE | SEE SERVICE BULLETIN NOV/DEC 1988 ISSUE 6 | |
| PHILIPS | N/A | 26G1 | POOR VIDEO | CHECK/REPLACE C249 | |
| PHILIPS | N/A | 26G1 | POOR AFT LOCK - ADJUSTING AFT DETECTOR HELPS BUT DOESN'T COMPLETELY CORRECT | CHECK/REPLACE Y200 SAW FILTER (P/N# 483515497068) | |
| PHILIPS | N/A | 26G1 | POWER SUPPLY GOES INTO SHUTDOWN AT POWER ON OR CHANNEL CHANGE OR SCENE CHANGES. | CHECK/REPLACE R433 (115K) FOR CHANGE IN VALUE. | |
| PHILIPS | N/A | 26G1 | BEAT IN THE PICTURE | CHECK/REPLACE R433 | |
| PHILIPS | N/A | 26G1 | BRIGHT SCREEN WITH RETRACE LINES,NO SOUND OR PIX AND SET CANNOT BE SHUT OFF - NO KEYBOARD FUNCTIONS | CHECK/REPLACE Z300 (MAY CHECK GOOD BUT LEAKY) | |
| PHILIPS | N/A | 26G1 | POOR HORZ. HOLD,PIECRUSTING,BENDING,ETC. | REPLACE AVJ034A001 JACK PANEL | |
| PHILIPS | N/A | 26G1 | REDUCED LDR RANGE AND LED BRIGHTNESS | INSTALL 47K AT JUMPER B397-R91 2.4k R261 4.3k | |
| PHILIPS | N/A | 26G1 | DEAD SET WITH Q420 SHORTED AND R430 OPEN | REPLACE D448,Q420 AND R430 | |
| PHILIPS | N/A | 26G1 | LOUD RUSHING SOUND W/RETRACE BEFORE GOING OUT | CHECK Z300 | |
| PHILIPS | N/A | 26G1 | WASHED OUT VIDEO - OSD GRAPHICS ARE PERFECTLY NORMAL | CHECK/REPLACE Q641,Q642 AND Q643 FOR E-B SHORTS | |
| PHILIPS | N/A | 26G1 | SECONDARY CONTROLS LOCK-UP AFTER 30 MINUTES OF OPERATION ALSO THE OSD GRAPHICS ROLL VERTICALLY | CHECK/REPLACE D306 | |
| PHILIPS | N/A | 26G1 | SNOWY RASTER AND AUDIO FROM ONE CHANNEL IS ALL THAT CAN BE HEARD - CHANNEL NUMBER DOES CHANGE | CHECK/REPLACE TUNER OR PRESCALER IC INSIDE TUNER IC - (P/N# 483520987893) | |
| PHILIPS | N/A | 26G1 | INTERMITTENT AUDIO | REPLACE L307 | |
| PHILIPS | N/A | 26G1 | HIGH VOLTAGE PULSATES ON/OFF - NO PICTURE AND 130v B+ IS LOW | CHECK/REPLACE IC550 (LA7831) AND R445 (1 @ 1/2w) | |
| PHILIPS | N/A | 26G1 | DEAD SET | CHECK IC550 | |
| PHILIPS | N/A | 26G1 | NO VIDEO HAS JAIL BARS | CHECK Z670,R673,D670,C680 | |
| PHILIPS | N/A | 26G1 | POOR B+ REGULATION -- PICTURE FOLDS OVER IN THE CENTER OF SCREEN | CHECK/REPLACE IC400 (5303340001) OPTO-COUPLER | |
| PHILIPS | N/A | 26P1 | VOLTAGE AT Z430 IS NOT 5.6v | CHECK/REPLACE Z430 FOR CHANGE OF VALUE | |
| PHILIPS | N/A | 26P1 | NO HORZ. DRIVE FROM PIN 26 OF IC200 | CHECK/REPLACE C222 FOR OPEN | |
| PHILIPS | N/A | 26P1 | REMOTE 'OFF' BUTTON MUST BE PRESSED TWICE TO TURN SET OFF. | CHECK/REPLACE IR90 INFRARED RECEIVER | |
| PHILIPS | N/A | 26P1 | DEAD SET | CHECK/REPLACE Q420,D430,R427,R428 AND R424. | |
| PHILIPS | N/A | 26P1 | POWER SUPPLY GOES INTO SHUTDOWN AT POWER ON OR CHANNEL CHANGE OR SCENE CHANGES. | CHECK/REPLACE R430 (110K) FOR CHANGE IN VALUE. | |
| PHILIPS | N/A | 26P1 | NO VERTICAL SWEEP | CHECK/REPLACE R445 FOR OPEN | |
| PHILIPS | N/A | 26P1 | NO COLOR WHEN COLD | CHECK/REPLACE IC600 | |
| PHILIPS | N/A | 26P1 | NO COLOR AND VOLTAGES ON IC600 PINS#12,13,14 ARE LOW | CHECK/REPLACE IC600 | |
| PHILIPS | N/A | 26P1 | DEAD SET - 5 VOLTS NORMAL BUT RESET LINE LOW | CHECK/REPLACE IC351 | |
| PHILIPS | N/A | 26P1 | INTERMITTENT DEAD SET | CHECK/RESOLDER C431 | |
| PHILIPS | N/A | 26P1 | WASHED OUT PIX - CONTRAST CONTROL HAS NO EFFECT | CHECK/REPLACE Q661 | |
| PHILIPS | N/A | 26P1 | INTERMITTENT SHUTDOWN | CHECK/REPLACE R663 | |
| PHILIPS | N/A | 26P1 | NO COLOR ON SOME CHANNELS-INT. LOSS OF COLOR | CHNG. C620 TO 10pF | |
| PHILIPS | N/A | 26P1 | LOW B+ AND NO RASTER | CHECK/REPLACE IC400 | |
| PHILIPS | N/A | 26P1 | INTERMITTENT OPERATION - LEDS WOULD LIGHT FOR A SECOND | CHECK/RESOLDER CONECTIONS ON C451 (NEAR FLYBACK) | |
| PHILIPS | N/A | 26P1 | DISTORTED AUDIO W/SET ON--HUM OR BUZZ W/SET OFF | C284 AND/OR C294 MISSING --CHECK FOR PRESENCE OF | |
| PHILIPS | N/A | 26P1 | NO VIDEO | CHECK/REPLACE C608 FOR SHORT AND R622 FOR OPEN | |
| PHILIPS | N/A | 26P1 | HIGH FREQUENCY SQUEAL | REPLACE L421 | |
| PHILIPS | N/A | 26P1 | POOR REGULATION AFTER Q420 WAS REPLACED | REPLACE R427,R428 AND R424 | |
| PHILIPS | N/A | 26P1 | DEAD SET WITH NO STANDBY POWER | CHECK/REPLACE Q420 AND R424 | |
| PHILIPS | N/A | 26P1 | PIP DISAPPEARS ON VIDEO GAMES | DO NOT ATTEMPT TO USE PIP WITH NON STANDARD SIGNALS | |
| PHILIPS | N/A | 26P1 | ROLLING/FLAGING/HORZ. TEARING AT TOP OF PICTURE | REPLACE IC200 WITH NEW VERSION (TDA4505B) (USE 483531057062) | |
| PHILIPS | N/A | 26P1 | SET COMES ON WITH AUX.VIDEO BUT TUNER AUDIO | REPLACE IC350 WITH NEW VERSION | |
| PHILIPS | N/A | 26P1 | SET SHUTS DOWN BUT WITH SCREEN CTRL. ALL THE WAY DOWN, THE SET WILL REMAIN TO RUN WITH WHITE SCREEN WITH RETRACE. | CHECK/REPLACE R11 (100 OHM) ON THE CRT BOARD -- (200 VOLT SOURCE) | |
| PHILIPS | N/A | 26P1 | SET SHUTS OFF INT. OR WON'T EVEN COME ON | CHECK C431 OR CONNECTIONS ON IT | |
| PHILIPS | N/A | 26P1 | SET WILL COME ON ONCE AND THEN WON'T SHUT OFF OR IT WILL SHUT OFF AND NOT COME BACK ON. | CHECK/REPLACE IC350 (MICRO-PROCESSOR) | |
| PHILIPS | N/A | 26P1 | DEAD SET ,POWER SUPPLY FAILURE | CHECK TO SEE IF R429 IF TOUCHING C450 | |
| PHILIPS | N/A | 26P1 | SLOW OR NO COLOR LOCK POSSIBLY ON SOME CHANNELS ONLY AND THIS SET DID HAVE NEW STYLE CRYSTAL WITH BLUE MARKINGS. | CHECK/REPLACE IC600 | |
| PHILIPS | N/A | 26P1 | NOISY OR SQUEALING SOUND COMING FROM SWITCHING TRANSFORMER | CHECK/REPLACE R410 OR R421 FOR OPEN | |
| PHILIPS | N/A | 26P1 | HISS IN SPKRS. W/TV OFF--POP IN SPKR AT TURN ON | REMOVE D280 AND INSTALL NEW DIODE P/N 4835 130 37048 | |
| PHILIPS | N/A | 26P1 | 130 VOLT SOURCE IS TOO LOW | CHECK/REPLACE R431 AND IC400 | |
| PHILIPS | N/A | 26P1 | JAIL BARS ON THE LEFT SIDE OF THE SCREEN | CHECK/REPLACE L502 WITH NEW TYPE (483515757336) | |
| PHILIPS | N/A | 26P1 | RELAY CHATTERS | CHECK/REPLACE C405 FOR OPEN | |
| PHILIPS | N/A | 26P1 | REPEATED FAILURE OF Q420 (FET) | CHECK/REPLACE C412 WITH A 100nF (MAY HAVE A 10nF FROM THE FACTORY) | |
| PHILIPS | N/A | 26P1 | TUNING SLOW TO LOCK IN WHILE IN THE CABLE MODE | REPLACE THE MICROCOMPUTER IC | |
| PHILIPS | N/A | 26P1 | 130 VOLT SOURCE IS TOO HIGH | CHECK/REPLACE R430 AND R432 FOR A CHANGE IN VALUE | |
| PHILIPS | N/A | 26P1 | DEAD SET AFTER MANY POWER SUPPLY COMPONENTS CHANGED | CHECK L422 FOR OPEN | |
| PHILIPS | N/A | 26P1 | R429 GETS VERY HOT AFTER A FEW MINUTES | CHECK C430 FOR SHORT ALSO D430 | |
| PHILIPS | N/A | 26P1 | SET IS SHUTTING DOWN | CHECK/REPLACE R11 (CRT BOARD) FOR OPEN | |
| PHILIPS | N/A | 26P1 | NO COLOR | CHECK/REPLACE R614 FOR A CHANGE IN VALUE | |
| PHILIPS | N/A | 26P1 | BRIGHT SCREEN WITH RETRACE LINES | CHECK/REPLACE R663 FOR OPEN | |
| PHILIPS | N/A | 26P1 | SET WILL NOT TURN OFF EVEN BY GROUNDING COLLECTOR OF Q433 | CHECK/REPLACE IC402 | |
| PHILIPS | N/A | 26P1 | BLOWS Q420 IMMEDIATELY | CHECK D430 FOR SHORTS | |
| PHILIPS | N/A | 26P1 | SLOW COLOR LOCK AFTER CHANNEL CHANGE | USE SELECTED CRYSTAL WITH BLUE MARK ON CASE | |
| PHILIPS | N/A | 26P1 | SET SHUTS DOWN DURING SCENE CHANGES OR CHANGING CHANNELS | CHECK/REPLACE D661,R663 AND Q661 | |
| PHILIPS | N/A | 26P1 | SLOW CHANNEL ACQUISTION IN THE CABLE MODE | CHECK/REPLACE IC380 (5 VOLT SOURCE) | |
| PHILIPS | N/A | 26P1 | SET GOES OFF INTERMITTENTLY--APPEARS TO SHUTDOWN | CHECK FOR CORRECT SETTING OF THE B+ (130 VOLTS) | |
| PHILIPS | N/A | 26P1 | DEAD SET AND RESET PIN #33 STAYS AT 1.5 VOLTS | CHECK/REPLACE IC351 | |
| PHILIPS | N/A | 26P1 | HIGH PITCHED SQUEAL FROM POWER SUPPLY WHILE ON | REPLACE L421 USING ONLY P/N 483515757054 | |
| PHILIPS | N/A | 26P1 | BRIGHT SCREEN WITH RETRACE LINES - NO VIDEO | CHECK Q630,Q631,Q632 | |
| PHILIPS | N/A | 26P1 | VERTICAL SWEEP STRETCHED SEVERLY | CHECK/REPLACE IC550 | |
| PHILIPS | N/A | 26P1 | ERRATIC OSD WHEN SET IS HOT | CHECK/REPLACE IC350 | |
| PHILIPS | N/A | 26P1 | SET TURNS ON THEN MICROPROCESSOR LOCKS UP - WILL NOT TURN BACK OFF - SNOWY RASTER LOCKED ON ONE CHANNEL | CHECK/REPLACE Q337 | |
| PHILIPS | N/A | 26P1 | NO AUDIO OR VIDEO BUT OSD WORKS OK | CHECK/REPLACE L210 | |
| PHILIPS | N/A | 26P1 | INTERMITTENT SHUTDOWN AND INTERMITTENT HORZ. DRIVE | CHECK/REPLACE C208 FOR LEAKAGE | |
| PHILIPS | N/A | 26P1 | INTERMITTENT SHUTDOWN OR INTERMITTENT START-UP | CHECK FOR COLD SOLDER CONNECTIONS ON D430 OR C431 | |
| PHILIPS | N/A | 26P1 | SET SHUTS OFF AT RANDOM | CHECK/REPLACE IC350 | |
| PHILIPS | N/A | 26P1 | OSD GOOD BUT NO OFF-AIR VIDEO | CHECK L210 LEAD DRESS (POSSIBLY SHORTING TO ITS OWN SHEILD) | |
| PHILIPS | N/A | 26P1 | VERTICAL ROLL ON SOME CABLE CHANNELS | CHANGE R603 TO A 2k | |
| PHILIPS | N/A | 26P1 | RADIO INTERFERENCE,DOTS,SWIRLS OR HERRINGBONE SEEN ON PIP VERSIONS. | CHECK/REPLACE PIP MODULE (ISOLATE BY UNPLUGGING J602) | |
| PHILIPS | N/A | 26P1 | OSD MENU SKIPS THE STEREO AND AUX INPUT FEATURES | CHECK/REPLACE D261 | |
| PHILIPS | N/A | 26P1 | BENDING OR TEARING OF THE PIX - MAYBE THERMAL AND ALSO VARY FROM SIGNAL AND AGC LEVELS. | REPLACE IC200 (483520987072) |